STORMTROOPER E-11 COMPLETE ANH E-11 BLASTER KIT OFFER

AS DETAILED IN THE PICTURE ABOVE THIS COMPLETE KIT WILL GIVE YOU A FIRST CLASS STERLING REPLICA AND GREEBLIES WITH WHICH TO CREATE YOUR OWN MOVIE ACCURATE E-11 YOU WILL ONLY NEED TO ADD THE  SCOPE RAIL TO COMPLETE YOUR ANH E-11 WE EVEN INCLUDE THE HARD TO FABRICATE MAGAZINE CYLINDERS

THE WHOLE KIT IS ACTUALLY CONSTRUCTED FROM TWO, YES YOU READ RIGHT TWO ORIGINAL STERLING SUBS ONE THAT WAS CUT UP TO RETAIN AS MUCH OF THE DETAILING BODY PARTS AS POSSIBLE AND THE OTHER WAS CUT UP TO RETAIN AS MUCH OF THE MAIN BODY AS POSSIBLE

WITH THIS IS MIND WHAT YOU GET FOR A FRACTION OF THE COST OF HACKING UP TWO DEACTIVATED SUBS  IS AN IMPRESSIVE LIGHTWEIGHT 1:1 DETAILED CAST OF THE COMPLETE MAIN BODY EXACT TO THE GENUINE DIMENSIONS AND ALL THE PARTS TO REASSEMBLE A COMPLETE 1:1 COPY OF A STERLING 

ON THE MAIN BODY ALL THE VENT HOLES THAT ARE NOT COVERED BY A BARREL FIN ARE OPEN EXCEPT FRO THE ONES UNDER THE FORWARD STOCK TO GIVE YOU AS MUCH AREA TO GLUE TO BUT THEY ARE STILL THERE IN RELIEF DETAIL SO YOU CAN DRILL THEM OUT IF YOU REALLY WANTED TO 

ONE OF THE HARDEST THINGS TO OBTAIN AND GET RIGHT IS THE FINS SO TO SAVE TIME AND HASSLE WE HAVE INCLUDED THE ALREADY MOULDED IN PLACE  SO THE REMAINING BARRELS VENTS HAVE BEEN COVERED BY HIGHLY DETAILED BARREL FINS THAT LOOK AS IF THEY REALLY GO INTO THE FINAL VENT HOLES THEY HAVE EDGE SEAMS SO DON'T ACTUALLY  LOOK MOULDED IN  AND IN SOME PLACES THE REMAINING VENTS CAN JUST BE SEEN UNDERNEATH  SO CAN BE VIEWED UP NICE AND  CLOSE WHEN OUT TROOPING BUT AS THEY SAY A PICTURE IS WORTH A THOUSAND WORDS

ALL SERIAL NUMBERS AND MARKING ARE VISIBLE ON THE MAIN PARTS WE HAVE ALSO ADDED REGISTRATION MARKS TO THE MAIN BODY TO SHOW THE PRECISE LOCATION OF THE MAIN GRIP, THE MAGAZINE HOUSING THE REAR SIGHT AND REAR END CAP LOCK IF YOU ALIGN THE GRIP AND MAGAZINE AT A RIGHT ANGLE TO EACH OTHER AND IN THE MARKED POSITION THEY WITH BE EXACTLY AS PER THE ORIGINAL STERLING

IT SHOULD BE VERY EASY TO ASSEMBLE EVEN FOR THE MOST NOVICE OF BUILDER IT REALLY  IS JUST GLUE AND PLACE EVEN THE MOLD LINE IS ON THE UNDERSIDE SO THE CLEAN UP IS REALLY SIMPLE WITH OVER 90% HIDDEN BY THE GRIP, STOCK, AND LOCK  ITS JUST AN INCH BEHIND THE GRIP AND AN INCH FRONT OF IT

THE PARTS ARE FIRST GENERATION CASTS FROM 2 GENUINE STERLING SUBS AND HAVE BEEN MODIFIED SLIGHTLY TO REFIT AROUND THE MAIN BODY WITH ADDITION OF 38MM RADIUS SO THAT THEY SIT FLUSH TO THE BODY AND CAN BE GLUED  WITHOUT THE NEED FOR MAJOR SURGERY OR EXCESSIVE FILLING

OK ABIT MORE DETAIL THAT THE PHOTO'S DO NOT SHOW, THE MAIN BODY IS ACTUALLY HOLLOW SO YOU COULD EVEN FIT A  DUMMY SPRING INTO THE MAIN BODY TOO AND THE FRONT BARREL END IS OPEN SO IT WOULD BE ADVISABLE TO PAINT THE TIP ORANGE DEPENDING ON YOU COUNTRIES REGULATIONS THE KIT IS SUPPLIED IN WHITE TO CREATE A NICE WHITE BLASTER WHICH YOU COULD REPAINT TO YOUR PREFERRED COLOUR IF YOU WISH

YOU GET EVERYTHING DETAILED BELOW THAT YOU NEED TO BUILD YOUR OWN DETAILED 1:1  ANH E-11 APART FROM THE SCOPE RAIL

THIS KIT CONTAINS

REMEMBER

YOU WILL NEED TO SUPPLY YOUR OWN METAL SCOPE RAIL

THESE PARTS ARE CAST IN HIGH GRADE 2 PART POLYURETHANE RESIN

WE DONT SUPPLY ANY OF OUR KITS TO THIRD PARTY RESELLERS IF YOU DID'NT BUY IT FROM DOOPYDOOS OR THE FREAK THEN YOU JUST BOUGHT A SUB STANDARD COPY FROM A RECASTER

1 MAIN GRIP

2. SELECTOR SWITCH

3.TRIGGER GUARD

4 TRIGGER

5. EJECTOR PORT SHROUD

6. FORWARD VENT GUARD

7. REAR UNDERSTOCK SECTION

8. FORWARD UNDERSTOCK SECTION

9. COCKING LEVER

10. REAR END CAP LOCK

11 HOLLOW REAR END CAP

12. REAR SIGHT

13.MAIN MAGAZINE RECEIVER BODY

14. CUT DOWN MAGAZINE

15. MAGAZINE RETAINING SCREW 

16. BAYONET LUG (yes really even this is included)

17. FRONT SIGHT

18. MAIN STERLING BODY SECTION

19. 1st GEN CAST OF A M38 SCOPE

20. 1st GEN CAST OF A HENGSTLER COUNTER BOX

21. MAGAZINE CYLINDERS